RP2350B (two ARM cores at 252 MHz — one runs Python, one paints HDMI;
315/378 MHz via screen(mode, clock)) · 512 KB SRAM
(framebuffers) · 8 MB PSRAM (the Python heap) · 16 MB flash (12 MB
filesystem at /) · CYW43 Wi-Fi/Bluetooth on an RM2 module ·
PCM5102 audio DAC → 3.5 mm stereo jack · DS3231 battery-backed clock
(CR2032) · CH334U 4-port USB hub for keyboard/mouse/touch · micro-SD
slot, hot-swappable.
| Item | Purpose |
|---|---|
| USB-C | power in (2 A supply recommended — the hub passes up to 2 A on) and the serial console (CH340 → GP8/9, 115200 8N1) |
| Power switch | push-on / push-off, on the USB-C feed |
| Prog (micro-USB) | firmware flashing only — with USB HUB switch at DISABLE |
| USB HUB switch | ENABLE = keyboard sockets live; DISABLE = Prog port live |
| BOOT + RESET | hold BOOT, click RESET → UF2 drive appears on a PC |
| HDMI | to any monitor/TV |
| SYSTEM I2C (QWIIC/Qw/ST) | plug-in I2C modules — GP20/21, 3.3 V, 10 K pull-ups fitted |
| HEARTBEAT jumper | LED1 source: CYW43 position (normal —
Pin("LED")) or GP25 (only for boards built without
the wireless module — GP25 is the CYW43 chip-select otherwise) |
| DEBUG header | SWD (CLK/DAT/GND) — C-level debugging |
USB HUB switch → DISABLE · connect Prog to PC · hold
BOOT, click RESET · drag
firmware.uf2 onto the drive that appears · switch back to
ENABLE. Files and settings survive reflashing.
GP21 GND I2C0 SCL (bus shared with QWIIC + DS3231)
GP20 +5V I2C0 SDA
GP45 GP46 \
GP43 GP44 | GP40-GP46 are ANALOGUE inputs (machine.ADC)
GP41 GP42 |
GP39 GP40 /
GP37 GP38
GP35 GP36
GP26 GP34
GP07 GP06
GP05 GP04
GP03 GP02
GP01 GP00
VCC VCC 3.3 V out (3.3 V logic; 5 V powers, never GPIO)
GND GND
Every GP pin: digital in/out and PWM. GP32 = DS3231
alarm INT (open-drain, active low — ds3231.alarm_pin()
supplies the pull-up); GP27 = DS3231 32 kHz output
(enable a pull-up to use).
machine.Pin)GP8/9 console UART · GP12–19 HDMI · GP28/30/31/33 SD card (SPI1) ·
GP10/11/22 audio I2S · GP23/24/25/29 wireless · GP47 PSRAM CS. The
status LED is Pin("LED") (on the wireless chip). Full
table: manual §2.
| Mode | Pixels | Colours | Clock (MHz) |
|---|---|---|---|
RGB640 (default) |
640×480 | 256 (8-bit) | 252 / 315 / 378 |
RGB320 |
320×240 (doubled) | 65,536 (16-bit) | 252 / 315 / 378 |
RGB320_8 |
320×240 (doubled) | 256 (8-bit) | 252 / 315 / 378 |
RGB512 |
512×300 (doubled to 1024×600) | 65,536 (16-bit) | 252 |
RGB1024 |
1024×600 native | 16 (palette) | 252 |
RGB640_4 |
640×480 | 16 (palette) | 252 / 315 / 378 |
hdmi.layer()) is
available in RGB320 and RGB320_8.RGB640_4 and RGB320_8 are the
fast-SRAM modes: the off-screen create()
buffer fits in the spare video SRAM rather than the slower PSRAM, for
double-buffered composing that never stalls. RGB320_8 is
the only mode offering the overlay and a fast double buffer at
once.console("none") hides output — type console()
blind to recover./settings.json.